Showing results: 106 - 120 of 435 items found.
-
Circuit Check, Inc.
Circuit Check’s in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading ICT handlers including Keysight 5i, Teradyne TSh Multi-Site, IPTE and Pematech. Circuit Check is the go-to partner for in-line functional test fixtures to speed production throughput.
-
VECTOR Electronics and Technology, Inc.
Card edge board for STD and S-100 bus specification card size and edge contacts on tabs. Available with different circuit patterns for prototyping applications.
-
MFA Family -
Langer EMV-Technik GmbH
The micro probes allow detailed measurements of high-frequency magnetic fields in the layout, at the smallest SMD components(0603-0201) and at IC pins of printed circuit boards.
-
SG-L09 -
Jinge Testing Machine Co.,Ltd
This machine is used for testing the adhesive strength of copper-foil circuit on the PC board or tin-foil, aluminum-foil, tap,…etc, which are adhered to rhe suface of object.
-
Canadian Microelectronics Corp.
This fixture clamps to microstrip or CPW lines at the edge of an RF board and is usable at any position without limit on size of circuit. The base is magnetic and it can be locked and released by a knob to accommodate any kinds of circuit configuration. Available for frequency ranges up to 40 GHz.
-
ECT
Functional testing is done to insure that a completed printed circuit board will operate correctly in the final product. Failures detected at this time will consist of interactional problems between components. Testing here can be used to set board variables such as timers or limiters to proper settings.
-
4946 -
Technobox, Inc.
The HDD is positioned midway such that the PMC component envelope is not violated. Furthermore, steel rails are attached to the printed circuit board, allowing for a secure, robust installation of the hard disk drive. This is a superior mechanical approach, compared with other printed circuit board-based solutions available on the market.
-
Test Tooling Solutions Group
Probe pin is also known as pogo pin or spring probe. It is designed to test the connection between two circuit boards and devices or equipment under test.
-
PCI-AI12-16(A) -
Acces I/O Products, Inc.
Model PCI-AI12-16 is a multifunction, high-speed, analog-to-digital converter board for use in PCI-Bus computers. It accepts up to 16 single-ended or eight differential inputs. The board uses a low-noise, multilayer printed circuit board. Inputs are protected against overvoltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts.
-
PCI-AI12-16A -
Acces I/O Products, Inc.
Model PCI-AI12-16 is a multifunction, high-speed, analog-to-digital converter board for use in PCI-Bus computers. It accepts up to 16 single-ended or eight differential inputs. The board uses a low-noise, multilayer printed circuit board. Inputs are protected against overvoltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts.
-
0001026-1 / -2 -
VI Control Systems Ltd.
VI Control Systems has designed two converter boards that make it easy to connect data acquisition boards to breadboards and allow easy computer control and monitoring of prototyped electronic circuits. The converter boards are 0.8 x 3.5 inches and have silk-screened pin numbers for every pin on the board. The 68-pin SCSI converter can also be used to connect 68-pin SCSI cables to prototype solder boards that have 0.1 inch centers.
-
Circuit Check, Inc.
Circuit Check supports reading linear bar codes and 2D symbols within each of its fixture product lines.When spring-loaded probes are not practical or access is limited, Circuit Check can help you with thru-connector tests to contact connectors on any surface or edge of a circuit board. These tests can be implemented spring probes, mating connectors, sacrificial SMT connectors, and stabber cards.
-
VECTOR Electronics and Technology, Inc.
Boards for 96 and 160-pin DIN Eurocard plug-in application with option to mount DIN 41612 type connectors on ends. Available with different circuit patterns for prototyping applications.
-
Mill-Max Mfg. Corp.
Mill-Max's BGA Socket/Adapter Systems are used for both socketing BGA devices and interconnecting circuit boards. Systems are available to fit 1mm, .050" and .8mm grid footprints.
-
Mounting On Circuit Board Or DIN Rail -
INELTA Sensorsysteme GmbH & Co. KG
*PCB mounting*Suitable as: setpoint device or rotary actuator*Compact in design* Robust aluminium housing* Gear safety clutch